AMTS 90/120/150 Tyre Carrier Spacer + Light Mount Option

[Guest Close Guest]

Hey amts... trying to PM you but your inbox is full.
I have a couple of questions re. your spacers.

cheers

Pat

Try now, or the email provided in the first post of this thread is more reachable.

[ceasar m Member Find all posts View Profile Close ceasar m]

Hi amts,
Is the bracket and pole bracket for 150 series still available? and a question similar to #324 post, once the bracket and pole holder installed can I still fit the spare cover,like to have the cover to hide the rear camera. Can you please be able to post the finished product for 150 series ,like to find out if the pole bracket is on the right side similar to post #295.
Thanks

[MYT150 Member Find all posts View Profile Close MYT150]

ceasar m,

I just fitted mine today and yes the light pole is on the right hand side, I used the grommet in the door for the camera wiring to run the wiring for the light, rather then the bolt with the hole in it, seemed to make more sense then adding another opening for dust to enter. While I had the carrier off I also removed the camera shroud so I can now see the bumper and the hitch.

You won't fit the cover with the spacer in place, as the tyre would be out to far for it to fit, if still screwed to the door, unless you left the tyre at home, but you would have to remove the light bracket as it sits right up against one of the screws that holds the backing case on.

Regards

Aidan

[ceasar m Member Find all posts View Profile Close ceasar m]

Hi Aidan,
Thanks for the reply , is there any chance to post photos of your install please. I still like to have my spare cover install if possible. I saw one of ours here in my area with Prado point sticker with same set up but instead he have the CB aerial. I think it was a Kaymar bracket. Anyway did you extend the wire for your camera or it just right ?

Regards,

Ceasar

[MYT150 Member Find all posts View Profile Close MYT150]

Ceaser,

Here are two photo's, I can get more in the morning if you want any specific ones. I can;t see any way to keep the cover and space out the tyre. I didn't need to extent the camera wire, but did need to take it off the factory clip where the connector is to get the extra length, and also it would not have been possible to reconnect it there as it was to hard to get to with the spacer bracket not allowing enough room for it to plug back in.

[Guest Close Guest]

Thanks Aidan.

[ceasar m Member Find all posts View Profile Close ceasar m]

Thanks Aidan .

[Brendos 150 Member Find all posts View Profile Close Brendos 150]

Here is my AMTS wheel spacer installed.

Didn't buy this directly from you. Found it on gumtree. Great product mate! ��������

[mullerwh Member Find all posts View Profile Close mullerwh]

Here is my AMTS wheel spacer installed. [ATTACH=CONFIG]21959[/ATTACH][ATTACH=CONFIG]21960[/ATTACH][ATTACH=CONFIG]21961[/ATTACH][ATTACH=CONFIG]21962[/ATTACH]

Didn't buy this directly from you. Found it on gumtree. Great product mate! ��������

Looks great Brendos ! Something that is on my list but first needs the tyres to go with it !
What brand and size tyre have you fitted?

Cheers

[ceasar m Member Find all posts View Profile Close ceasar m]

Looks great Brendos, same question with Mullerwh? Thanks for the PM sorry if I double click it.
Cheers

[bilo33prado Senior Member Find all posts View Profile Close bilo33prado]

Hi Andrew,

Are you still making these items? I have a 120 series.

Cheers
Geoff

[Guest Close Guest]

Hi Geoff
Yes I am

[teddy Lurker Find all posts View Profile Close teddy]

good evening AMTS do you have one for prado 150 with 2.8 Diesel engine .I am interested in getting one.Ta....Teddy

[Graz Senior Member Find all posts View Profile Close Graz]

You might find it quicker to get a response on his facebook page, AMTS 4x4

[Guest Close Guest]

Teddy, yes I do. Just short of the spacer bracket which is getting done this week.