Need some help, installed my new light bar, works fine, but half the switch always stays lit.. The words led lightbar always stay on, when you press the switch to turn it on then the picture of the bar lights up. Now I know it's not chewing too much battery but it shouldn't be on should it? Is it due to where the positives are connected to the battery? Not sure what it's called but you will know what I mean, where I've got it connect there's 4 spots to connect Are they all the same or is one of them only got power when the ignition is on?
Announcement
Collapse
No announcement yet.
Led switch light stays on
Collapse
X
-
1 of the contacts on the back of the switch is for dash light illumination. You tap into the dash lights cable/fuse. The LED lights message only then comes on when your lights are on so you can see the switch in the dark.2007 GXL V6 - ARB Bullbar with LED lights, snorkel, extractors, 2 1/4" dual exhaust, K&N filter, dimpled/slotted rotors, headrest dvd players, Ebay Satnav/reverse camera, GME 3100TX, Tigerz11 Side awning on custom brackets with Maxtrax mounts, 300W Invertor, ARB Underbody protection, Lightbar and STZ 265/70 tyres.
Wish list in order I'll get them: Sliders, 2" lift, E-locker, Winch bar with winch.
-
Does it stay on with all the lights switched off, parkers etc?HKB Electronics, manufacturer of the Alternator Voltage Booster, Silver 2008 D4D,Lifted,Underbody protection, Alternator Voltage Booster, Tiger Z winch, Lightforce DL, Air Horns, Tanami Drawers, Drop down fridge slide, Outback cargo barriers, Rotronics dual Battery system, Polaris GPS, HF/UHF/VHF, Radio speaker combiner, Long ranger water tank, Diff breathers, Inverter, Snorkel and others
Comment
-
Originally posted by 8legsman View Postwhere I've got it connect there's 4 spots to connect Are they all the same or is one of them only got power when the ignition is on?
I have the same switch - you hook into the dash-light circuit, easiest way to do this is to splice the other switches close to it (there are 1 or 2 unused plugs in that area where you installed the LED bar switch) think its the green wire.
- to splice on those small wires, I do the following
-- take the soldering iron and burn the wire-insulation a bit, pop it off with your nail.
-- solder the new wire into it and use some electrical tape to tidy it up.
Comment
-
Check out this link it has an explanation of how it should work at the bottom with examples. http://www.aironboard.com/online/pus...green-red.html
Of the car is off ant there is no light on the switch this is correct.
If the car is on an there is a light on the switch it is probably right if you have DRL, or the other factory switches are illuminated, can be hard to tell sometimes.
If the car is on and the headlights are on then it is correct.
And f the car is on and headlights on and you switch on the switch then both should be lighting up.
Would be easier to answer if you include model and year.2015 GX Prado 3L Auto, in the process of being fitted out.
Comment
-
Originally posted by MYT150 View PostCheck out this link it has an explanation of how it should work at the bottom with examples. http://www.aironboard.com/online/pus...green-red.html
Of the car is off ant there is no light on the switch this is correct.
If the car is on an there is a light on the switch it is probably right if you have DRL, or the other factory switches are illuminated, can be hard to tell sometimes.
If the car is on and the headlights are on then it is correct.
And f the car is on and headlights on and you switch on the switch then both should be lighting up.
Would be easier to answer if you include model and year.
Comment
-
Originally posted by 8legsman View PostIs it where I have the power for the switch connected. Both the power to the light bar and power to the switch are connected to the same spot, bottom right hand side. If I separate them and move the switch power to one of the other three would that resolve it?
http://s1070.photobucket.com/user/ja...pigib.jpg.html
Comment
-
The switches in the prado 12- are backlit whenever the lights are on, when you operate a
switch then the icon lights up, there are two lights in the switch in other words, if you turn
the dimmer down and they go out that is normal I would have thought and this seems to be
what your describing?.HKB Electronics, manufacturer of the Alternator Voltage Booster, Silver 2008 D4D,Lifted,Underbody protection, Alternator Voltage Booster, Tiger Z winch, Lightforce DL, Air Horns, Tanami Drawers, Drop down fridge slide, Outback cargo barriers, Rotronics dual Battery system, Polaris GPS, HF/UHF/VHF, Radio speaker combiner, Long ranger water tank, Diff breathers, Inverter, Snorkel and others
Comment
Comment