Announcement

Collapse
No announcement yet.

2020 VX KAKADU high beam source

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • 2020 VX KAKADU high beam source

    Hi folks, apologies if this was covered elsewhere. 2019/20 VX & KAKADU have dual LED headlight. Trying to find high beam trigger wire to connect to the relay to turn on recently mounted driving lights. Weird arrangement for these LED headlight so unsure where to find wire to send power to the relay so spotties turn on. Anyone done it?
    Prado GXL 2012 Charcoal - Drifta Drawers, Cargo Barrier, Sidewinder Dual Battery kit, Ironman Bar, Narva lights, Safari Snorkel, Airbags, TX3350 kit, Waeco CFX65DZ - often seen with Thule 2.2M narrow roof pod and towing 2014 Kimberley Kamper. Could be anywhere!

  • #2
    you will need a special harness as the lights are canbus. use the search function to find posts already on this subject

    Found this...

    https://www.pradopoint.com.au/forum/...ight-bar-stedi


    https://www.pradopoint.com.au/forum/...-switch-canbus
    Last edited by blw; 25-03-2020, 07:08 PM.

    Comment


    • #3
      Thanks. The auto electrician is buying a wiring loom from Toyota to link the spotties to high beam. Another $150.
      Prado GXL 2012 Charcoal - Drifta Drawers, Cargo Barrier, Sidewinder Dual Battery kit, Ironman Bar, Narva lights, Safari Snorkel, Airbags, TX3350 kit, Waeco CFX65DZ - often seen with Thule 2.2M narrow roof pod and towing 2014 Kimberley Kamper. Could be anywhere!

      Comment


      • #4
        Strange wiring. Auto electrician bought the complicated wiring loom from Toyota. Could use the Aironboard Roo Lights dash switch but this does not illuminate st any time, when pushed in or otherwise. Lights are powered with relay that earths lights, rather than provides power, if I understand correctly. Automatic lights also provide an additional complication. Have not yet tested auto high beam yet, but lights work fine with manual high beam. Tricky

        The next challenge is to make it work with an illuminated switch.
        Prado GXL 2012 Charcoal - Drifta Drawers, Cargo Barrier, Sidewinder Dual Battery kit, Ironman Bar, Narva lights, Safari Snorkel, Airbags, TX3350 kit, Waeco CFX65DZ - often seen with Thule 2.2M narrow roof pod and towing 2014 Kimberley Kamper. Could be anywhere!

        Comment


        • #5
          A few replies and no one told him where to connect to the 'hi beam connector'.
          The links are no help either.

          Comment


          • #6
            cbp

            As it is a CanBus the easiest way to connect is to use the Toyota loom which comes with all instructions required.
            The links posted advise that. As you want to know where to connect to high beam, you connect under the steering column.
            '18 VX, Billies with Dobinson springs, Summit bar with Narva Enhanced Optics to help my old eyes

            Comment


            • #7
              I had a Canbus High beam interface module installed, I believe the CANM8. Youtube has further information on this.
              https://www.youtube.com/watch?v=bUKQXfWUFSo
              But seems relatively straight forward and I'm guessing that's what my installer did.

              Comment

              canli bahis siteleri bahis siteleri ecebet.net
              mencisport.com
              antalya escort
              tsyd.org deneme bonusu veren siteler
              deneme bonusu veren siteler
              gaziantep escort
              gaziantep escort
              asyabahis maltcasino olabahis olabahis
              erotik film izle Rus escort gaziantep rus escort
              atasehir escort tuzla escort
              sikis sex hatti
              en iyi casino siteleri
              deneme bonusu veren siteler
              casibom
              deneme bonusu veren siteler
              deneme bonusu veren siteler
              betticket istanbulbahis
              Working...
              X