Rig Build 120 D4D Grande - 'MLC'

[Lorenzo Senior Member Find all posts View Profile Close Lorenzo]

Hi MLC,

I just noticed you're running the Cooper ST's... What do you think of them? Can you remember what it cost you a corner? Looking at those too and am putting them up against the BFG AT

Cheers,
Loz

[MidLifeCrisis Out of control poster! Find all posts View Profile Close MidLifeCrisis]

Good to hear Ghost, Jooloooia Goolieard owes us for our efforts in stimulating the Aussie economy.

[Ghost Advanced Member Find all posts View Profile Close Ghost]

Good to hear Ghost, Jooloooia Goolieard owes us for our efforts in stimulating the Aussie economy.

To right MLC!! i have given my savings an absolute smashing in the last few weeks lol!!

will have to slow down for a couple of weeks to let my savings replenish, then continue lol

Cheers

[MidLifeCrisis Out of control poster! Find all posts View Profile Close MidLifeCrisis]

New signage on the border track:

[MidLifeCrisis Out of control poster! Find all posts View Profile Close MidLifeCrisis]

Some new bits arrived today. Two sets of LEDS for the ARB bar. One set for me and one for Matty. (thanks to 1Coolbanana)

The other bit is the replacement dual battery monitor. Gave up on version one as a mass fail and now trying this one.

[MidLifeCrisis Out of control poster! Find all posts View Profile Close MidLifeCrisis]

Redundant post

[craigm Addicted PP Member Find all posts View Profile Close craigm]

Once done I will put it on the dyno and get some measurements.

MLC, how much does it cost for a session on a Dyno?

[MidLifeCrisis Out of control poster! Find all posts View Profile Close MidLifeCrisis]

Not sure. The hubby of a girl that works for me has one. I think he is charging $70??? Need to check mate.

[craigm Addicted PP Member Find all posts View Profile Close craigm]

Cheers. I'd be very interested to know what my V6 is pumping out and whether or not it requires any work...

[MUMSRIG Avid PP Poster! Find all posts View Profile Close MUMSRIG]

Dyno sessions vary in cost. Usually depends on if any tuning is required.

Most are around the $90 to do a couple of power runs though...

I'll have to ask about mine MLC but I didn't think it was a 5V jobbie, however it requires a software upgrade to allow for the switching between tunes.

Mitch

[MidLifeCrisis Out of control poster! Find all posts View Profile Close MidLifeCrisis]

Dyno sessions vary in cost. Usually depends on if any tuning is required.

Most are around the $90 to do a couple of power runs though...

I'll have to ask about mine MLC but I didn't think it was a 5V jobbie, however it requires a software upgrade to allow for the switching between tunes.

Mitch

Oh! Might check into that.
A "soft" upgrade is about the most I can handle at my age, anything else causes a loss of blood pressure and fainting.........

[ondaboat Coopers Pale Ale Find all posts View Profile Close ondaboat]

Oh! Might check into that.
A "soft" upgrade is about the most I can handle at my age, anything else causes a loss of blood pressure and fainting.........

Lea....why do you put up with him??

[1coolbanana Avid PP Poster! Find all posts View Profile Close 1coolbanana]

So whats the deal with the hawse?
How come its no good?

[MidLifeCrisis Out of control poster! Find all posts View Profile Close MidLifeCrisis]

The bar sticks up about 10mm into the hawse opening. I'm no expert but I thinki that would mean an unsucessful recovery and shreading of the rope on the first attempt.

In fact I plan to cover that piece of metal with similar stuff to what they use when they cut in a Kaymar bar on a 150. Have no idea what its called but will do when I source some from ARB or similar. It is an disaster waiting to happen to my new rope.

Hope you can follow, I didn't take any pics. PS 1CB I know you are Trekky so don't deny it.

[MidLifeCrisis Out of control poster! Find all posts View Profile Close MidLifeCrisis]

Lea....why do you put up with him??

Love is blind Adam, luckily for me