For Sale: Various touring items off 150 series

[Schniff Member Find all posts View Profile Close Schniff]

Post a pic of the side steps

Here are some pics of the steps.
In the first one you can see on the bottom step how I've cut the angle off the chassis mount to facilitate the KDSS lines.



Here you can see how I modified the other mount. Yes it compromises the strength but is still far stronger than stock.



I've also cut the angle off the checkerplate so if the steps bend up they won't damage the sills.



The steps have been well used which is why I'm selling them at a fraction of the original cost.

[Schniff Member Find all posts View Profile Close Schniff]

I'll grab the clic on mount, let me know what postage is to Brisbane!

Paul

Brains, PM sent.

[Schniff Member Find all posts View Profile Close Schniff]

Sorry for the OT post, but how did you find the lower clicon mount (where your UHF hand piece is), did it leave any marks on the dash when you took it off and was it secure and strong enough to hold your hand piece without moving around?

I have been looking for something like this but didn't know they existed until you posted your thread.

The limiting factor is not the clicon, but the mount you attach to it. I mounted my iphone holder to the lower one and had to do some mods to make it stable. The clicon itself is stable. No marks, just double sided tape to remove.

[Schniff Member Find all posts View Profile Close Schniff]

Ok here are some pics of the radio surround and storage pocket.

The radio surround has a small hole filed back up the top and to the right where the cable for my TPMS went. You will also need to refit the air vents and hazard light switch from the one on your car. If you have a VX/Kakadu its easy enough to swap the grey plastic trim on this part for the silver one, its screwed in at the back.



In order to fit a double DIN unit you will need parts 86212 ans 86211 from this diagram:

http://www.toyodiy.com/parts/p_G_201...AEYQ_8601.html

You will also need the fillers found here:
http://www.ministryofbass.com.au/mos...t-bracket.html

Below is the GX radio surround. As it tapers in from the front I had to cut sections out of the sides so my ICOM could fit in. At the back are the holes for the power/antenna cables. You cannot see any of the holes provided a radio is fitted in there.

[hulbyw Senior Member Find all posts View Profile Close hulbyw]

PM sent re battery tray if still available

[outback7 Banned Find all posts View Profile Close outback7]

Well, I am about to put my 150 up for sale and have taken a whole bunch of items off it which won't go onto the next car.
I am located in Adelaide if anyone wants to view the items.

TG150 Transfer Case guard in as new condition $100





Brown Davis Sump/Steering guard with a few knocks $90

5 x CSA Explorer wheels and 1 x Speedy Avalanche 17 x 7.5 wheels P25 offset fitted with Cooper ST-C 265/70 tyres. There is plenty of tread left. Would also suit 120 series. $1000

Oldaz Loadrail Steel Side steps. Passenger side modified to suit KDSS vehicle. Driver side has copped a ding. Would suit someone who would prefer to damage these than the factory steps. Cost $900 new, sell for $200.

Pirahna 4x4 Battery Tray in good condition $90.

Prado GX upper radio surround. This will suit anyone with GXL and above who wants to fit an aftermarket double DIN unit. It cost hundreds to buy genuine off Toyota, will sell for $100.

Prado GX lower console storage area. I modded this to fit my ICOM IC-400 Pro, EGT guage and dual battery monitor. It has holes drill into it, but would suit anyone who wants to have a similar setup. Sell for $80.

Clicon upper dash mount. Enables you to fit phone cradles or other widgets without drilling holes. $25.
I have the lower dash mount too, but its at the bottom of a box somewhere.

Below you can see a pic of the setup I had inside the vehicle. The TPMS is stuck to the upper clicon mount.


I would consider postage for some of the smaller items, however the larger ones would be for pickup only.
I also have recovery points which I might take off and autocraft suspension including polyairs if anyone would be interested.

Mate.....i hope you don't mind me asking. What will be your next car?

[hulbyw Senior Member Find all posts View Profile Close hulbyw]

Hi Schniff. Did you get my PM about the battery tray? Need to start sorting the new truck for a High Country trip