EOI - Carling rocker switches

[D4D-GXL Advanced Member Find all posts View Profile Close D4D-GXL]

I've been looking into purchasing carling rocker switches for the Toyota in bulk but before I do, I want to find out if anyone is interested in purchasing them as it's not worth the effort just for myself to buy in bulk so I'm putting feelers out there to see what people are after. I have attached a picture of what they are and there are many types of covers to suit your needs. Please PM me if you are interested stating how many and what sort of colour LEDs and covers you are after such as blue, red, orange, white, green, fog lights, spot lights, aux battery, awning lights, compressor etc.

i am expecting these switches to cost about $10 each compared to $19-$25 on eBay.

[pjorek Advanced Member Find all posts View Profile Close pjorek]

Can you get custom writing/pictures on these?

Also the couple of switches that nobody seems to supply is some sort of safety version switch. For instance if you have front/rear lockers you do not want to flick one on accidently whilst driving 100km/h on the freeway. A push and hold for (let's say 2seconds) switch would be ideal for that sort of stuff. These sort of switches are available out there just not in rocker/ARB version.

[fridayman Senior Member Find all posts View Profile Close fridayman]

I would be interested in a few. Maybe 3 or 4.

[D4D-GXL Advanced Member Find all posts View Profile Close D4D-GXL]

Hi Pjorik, I believe you can get custom stickers on the rocker switches but I have to buy at least 100 at a time. So unless there is lots of interest I a certain design then I can't foresee the manufacturer doing a one off. These particular switches are laser etched.

[4wd26 Junior Member Find all posts View Profile Close 4wd26]

I have a list of around 10 that I need
8 are common
But I would be interested in 2wd low and TC lockup

Also switches need to be led and have accessories bar light as well as on lights
I have noticed some of the cheaper options/ switches don't have this

[Jus10 Member Find all posts View Profile Close Jus10]

Any of these Carling Switches to any PP member in any quantity at wholesale price:
http://www.ionnic.com/electrical/swi...ra-series.html

[Beach Advanced Member Find all posts View Profile Close Beach]

Do we have to quote anything when ordering?

[znelbok Member Find all posts View Profile Close znelbok]

If I understand correctly, these don't fit inside the switch holes on the dash for either the 120 or the 150.

I just purchased one for the 150 that fits like an oem (with LED's) from Air On Board shop on ebay and three for my 120 from the same. Customrockers.com.au also have 120 switches that look oem. http://www.customrockers.com.au/epag...%20SWITCHES%22

The 120 takes a 21 x 39mm (17 x 36mm cutout) switch, the 150 takes 21 x 32mm

These I think are 21 x 37mm

Not as cheap as what is on offer here though, but worth a mention if you want an OEM looking switch

Mick

[Jus10 Member Find all posts View Profile Close Jus10]

Do we have to quote anything when ordering?

No need to quote in particular - just that you are a PPer. Send your enquiry to the [email protected] address. Any problems or questions pls PM me.

[Jus10 Member Find all posts View Profile Close Jus10]

If I understand correctly, these don't fit inside the switch holes on the dash for either the 120 or the 150.Mick

You are 100% correct - the mounting hole needs to be enlarged a tad to get the Carlings to fit.

[mjrandom Out of control poster! Find all posts View Profile Close mjrandom]

On the 150 it is more than a tad as the hole is 8mm shorter.

[Jus10 Member Find all posts View Profile Close Jus10]

On the 150 it is more than a tad as the hole is 8mm shorter.

ok, a tad +/-8mm .......

[Guest Close Guest]

Try here http://www.gumtree.com.au/s-ad/bray-...tch/1044915410

[Bushbasher Out of control poster! Find all posts View Profile Close Bushbasher]

You are 100% correct - the mounting hole needs to be enlarged a tad to get the Carlings to fit.

That's where a soldering iron comes into play. I took to the front panel on the centre console for mine.

[D4D-GXL Advanced Member Find all posts View Profile Close D4D-GXL]

I don't think there are enough people onboard to enable an import. Especially since the least amount of switch covers I can get imported are 100 or each type. That would take a very long time to recoup the costs. I think the bray park option may be a cheaper alternative for all. Thanks for the replies.