What did you do to your 150 today?

[Skprado Member Find all posts View Profile Close Skprado]

Would you try and source clear lenses or leave them red if they were changed work/rev light

Hard to find clear lense. And we can put only i think 23 or 28 watt bulb max thats what written on the light. But what i was thinking to do is to put 6 led small work light. For that have to cut in the plastic part. And than that will fit. These led lights are not big. And will look good as well n bright.

Like this https://www.ebay.com.au/itm/251735685750

[Skprado Member Find all posts View Profile Close Skprado]

Im in Northcote.

Not that far from me i am in cranbourne north.

[rackxp Junior Member Find all posts View Profile Close rackxp]

Was bored on weekend so install led globes in rear fog lights/ reflectors. They work with headlight on.

Any chance of a write up?

[Ian Reid Advanced Member Find all posts View Profile Close Ian Reid]

Had a full EGR clean, wee bit of gunk at 97k

[rackxp Junior Member Find all posts View Profile Close rackxp]

Had a full EGR clean, wee bit of gunk at 97k

[ATTACH=CONFIG]24986[/ATTACH]

Did you get that done in Toowoomba? What did it set you back?

[Drift Member Find all posts View Profile Close Drift]

Fitted a set of Solarscreens. What a difference.

[Ian Reid Advanced Member Find all posts View Profile Close Ian Reid]

Did you get that done in Toowoomba? What did it set you back?

Yes, had it done at home, sent you a P M with details

[AncientRuin Lurker Find all posts View Profile Close AncientRuin]

Maxtrax and shovel holder on Rhino rack pioneer platform

[craigm Addicted PP Member Find all posts View Profile Close craigm]

Maxtrax and shovel holder on Rhino rack pioneer platform

What a great idea....

[Fred63 Advanced Member Find all posts View Profile Close Fred63]

What a great idea....

Yes a great idea.
Thanks again craig.

[DGW Senior Member Find all posts View Profile Close DGW]

Got 5 new 265 x 70 x 17 Mickey Thompson Baja ATZ P3's fitted this morning. After 83k on MTZ's, certainly quieter and smoother on the drive home. Now just have to test them out properly.

[Secco Lurker Find all posts View Profile Close Secco]

Dual battery kit

I put a dual battery kit into my 150 prado. Got a laser cut bracket from off-road downunder to hold my bcdc battery charger, it fits nice and neat behind the air filter. Have a piranha battery tray that I had fitted by arb when they put my bull bar on. I ran he wire from the dual battery (97AH maintenance free) under the engine bay and along the chassis rail towards the boot. And feed the wire in through a grommet near the jack. And then installed a double cigarette socket and voltmeter on the pop out panel above the jacks door. All to run a 40L engle and have a spare socket for other accessories.

[cmilton54 Find all posts View Profile Close cmilton54]

Made six quick clamp slide in's to fit in the seat runners in the Kakadu. To strap down the engle.
The base was made out of 40x10mm aluminium bar with a 6mm threaded hole to hold down a p clip, with a couple of mudguard washers. I milled two runners on bar to fit into the slot. Alloy bracket was 40x27x10mm milled side was 7mm wide by 4mm deep, leaving a 13mm center section to fit into slide.

[steve.armitage Member Find all posts View Profile Close steve.armitage]

Fitted AMTS' RJ45 connector into the center console for my UHF radio mic

[Pearl150 Member Find all posts View Profile Close Pearl150]

Been to Baileys for injectors etc